Forge ahead in your certification aspirations, backed by the monumental wisdom encapsulated within the 350-801 dumps. Designed meticulously to echo the diverse spectrum of the syllabus, the 350-801 dumps unfold a vast tapestry of practice questions, nurturing an unerring command. Whether the succinct articulation of PDFs resonates or the captivating interactivity of the VCE format intrigues, the 350-801 dumps promise excellence. A robust study guide, intrinsically tied to the 350-801 dumps, deciphers the maze of concepts, ensuring you\’re well-prepared. Steadfast in our belief in these materials, we vehemently uphold our 100% Pass Guarantee.
Let the brilliance of our 350-801 VCE and PDF resources shine through in your 350-801 exam scores
Question 1:
When designing the capacity for a Cisco UCM 12.x cluster, an engineer must decide which VMware template will be used for each node. What is the lowest number of users supported in a template and the highest number of users in a template?
A. 750 and 15.000 users
B. 750 and 10.000 users
C. 500 and 10.000 users
D. 1000 and 10.000 users
Correct Answer: D
For Cisco Collaboration System Release (CSR) 12. x , the Unified CM deployments require all virtual nodes to increase their vRAM by 2 GB of memory for the following VM configuration templates:
1,000 users
–
2 vCPU
–
6 GB vRAM
–
80 GB vDisk
2,500 users
–
4 vCPU
–
6 GB vRAM
–
80 GB vDisk
7,500 users
–
2 vCPU
–
8 GB vRAM
–
110 GB vDisk
10,000 users
–
4 vCPU
–
8 GB vRAM
–
110 GB vDisk
Question 2:
What dialed number match this cisco UCM route pattern? 1[23]XX
A. 1200 through 1399 only
B. 1230 through 1239 only
C. 12300 through 12399 only
D. 1200 through 1300 only
Correct Answer: A
Question 3:
Refer to the exhibit.
An administrator accesses the terminal of a Cisco UCM and starts a packet capture. Which two commands must the administrator use on Cisco UCM to generate DNS traffic? (Choose two.)
A. show version active
B. utils diagnose test
C. show cdp neighbor
D. utils ntp status
E. utils diagnose module validate_network
Correct Answer: BE
Reference: https://ccxguru.wordpress.com/2018/02/03/behind-the-utils-diagnose-test/
Question 4:
An engineer is configuring a phone system CISCO UCM and wants to activate TFTP service. The engineer selects the serviceability page for configuration. Which nodes configurable for TFTP?
A. any two nodes
B. any node
C. only nodes that have Cisco UCM service enabled
D. any subscriber nodes
Correct Answer: C
TFTP is a network protocol that is used to transfer files between devices. It is often used to transfer firmware and configuration files to network devices. In order to use TFTP, the device must have a TFTP server configured. In Cisco UCM, the TFTP server is configured on the serviceability page. The TFTP server can be configured on any node that has Cisco UCM service enabled. The TFTP server cannot be configured on nodes that do not have Cisco UCM service enabled.
Question 5:
The security department will audit an IT department to ensure that the proper guidelines are being followed. The reports of the call detail records show unauthorized access to PSTN.
Which two actions should an administrator check to prevent the unauthorized use of the telephony system? (Choose two.)
A. Ensure that ad hoc conference calls are dropped if an external user is add.
B. Call forward settings (ALL/Busy/No Answer) are restricted to internal extensions in the network
C. Add an additional firewall between the Cisco UCM server and the Expressway Core server.
D. For extension mobility, logged-out CSS is restricted to internal extensions and emergencies.
E. Forced authorization code is used to recognize a dialing extension and authorize an international call.
Correct Answer: BE
Question 6:
A collaboration engineer must configure Cisco Unified Border Element to support up to five concurrent outbound calls across an Ethernet link with a bandwidth of 160 kb to the Internet Telephony Service Provider.
Which set of commands allows the engineer to complete the task without compromising voice quality?
A. dial-peer voice 1 voip translation-profile outgoing Strip9 max-conn 5 destination-pattern 91[2-9]..[2-9]……$ session protocol sipv2 session target ipv4:142.45.10.1 dtmf-relay rtp-nte sip-notify sip-kpml
B. dial-peer voice 1 voip translation-profile outgoing Strip9 max-conn 5 destination-pattern 91[2-9]..[2-9]……$ session protocol sipv2 session target ipv4:142.45.10.1 dtmf-relay rtp-nte sip-notify sip-kpml codec ilbc mode 20
C. dial-peer voice 1 voip translation-profile outgoing Strip9 max-conn 5 destination-pattern 91[2-9]..[2-9]……$ session protocol sipv2 session target ipv4:142.45.10.1 dtmf-relay rtp-nte sip-notify sip-kpml codec aacld
D. dial-peer voice 1 voip translation-profile outgoing Strip9 max-conn 5 destination-pattern 91[2-9]..[2-9]……$ session protocol sipv2 session target ipv4:142.45.10.1 dtmf-relay rtp-nte sip-notify sip-kpml codec mp4a-latm
Correct Answer: A
Question 7:
Which four requirements are mandatory to enable a mixed mode Cisco Unified CM cluster? (Choose four.)
A. Cisco CTL Provider Service activated and enabled
B. Cisco Certificate Authority Proxy Function activated and enabled
C. Cisco Trust Verification activated and enabled
D. Cisco CTL client
E. a minimum of one USB e-token
F. a minimum of two USB e-token
G. a minimum of one soft e-token
Correct Answer: ABDF
Question 8:
Which action is required if an engineer wants to have Cisco Unified Communications Manager control the configuration for an MGCP gateway?
A. Apply the ccm-manager configuration commands to the gateway.
B. Upload the custom configuration in the TFTP server in Cisco Unified CM.
C. From Cisco Unified CM > Device > Gateway > Add gateway, check the auto-configuration check box.
D. Configure the Cisco Unified CM\’s IP in voice service VoIP.
Correct Answer: A
Question 9:
An engineer builds this configuration on a Cisco IOS gateway for fax dial-peers:
Which command is required to complete the configuration?
A. Codec g726r32
B. Codec g729cr81
C. Codec g723ar63
D. Codec g711ulaw
Correct Answer: D
Reference: https://www.cisco.com/c/dam/en/us/td/docs/ios/voice/dialpeer/configuration/guide/xe_3s/vd_dp_se_3s_book.pdf
Question 10:
Callers from a branch report getting busy tones intermittently when trying to reach colleagues in other office branches during peak hours. An engineer collects Cisco CallManager service traces to examine the situation. The traces show:
50805567.000 |07:35:39.676 |SdlSig |StationOutputDisplayNotify |restart0 |StationD(1,100,63,6382) |StationCdpc(1,100,64,4725) |1,100,40,7.101980^*^* |[R:N-H:0,N:0,L:0,V:0,Z:0,D:0] TimeOutValue=10 Status=x807 UnicodeStatus= Locale=1 50805567.001 |07:35:39.676 |AppInfo | StationD: (0006382) DisplayNotify timeOutValue=10 notify=`x807\’ content=`Not Enough Bandwidth\’ ver=85720014.
What should be fixed to resolve the issue?
A. class of service configuration
B. geolocation configuration
C. region configuration
D. codec configuration
Correct Answer: C
Question 11:
What is required when deploying co-resident VMs by using Cisco UCM?
A. Provide a guaranteed bandwidth of 10 Mbps.
B. Ensure that applications will perform QoS.
C. Avoid hardware oversubscription.
D. Deploy the VMs to a server running Cisco UCM.
Correct Answer: C
When deploying co-resident VMs by using Cisco UCM, it is important to avoid hardware oversubscription. This means that you should not assign more resources to the VMs than the physical hardware can provide. For example, if you have a
server with 16 CPU cores, you should not assign more than 16 CPU cores to the VMs. If you oversubscribe the hardware, the VMs will not be able to get the resources they need to run properly. This can lead to performance problems and
even outages. To avoid hardware oversubscription, you should carefully plan your VM deployments. You should also monitor the performance of the VMs to make sure that they are not overusing the resources.
Here are some additional tips for deploying co-resident VMs by using Cisco UCM:
Use a virtualization platform that supports Cisco UCM. Make sure that the VMs have the correct operating system and software installed. Configure the VMs to use the correct network settings. Monitor the performance of the VMs to make
sure that they are running properly.
Reference:
https://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/uc_system/virtualization/collaboration-virtualization-sizing.html
Question 12:
Where would an administrator update learned patterns from the DNA UI?
A. System –> Enterprise parameters
B. Service –> Control Center –> DNA
C. Service –> Control Center
D. System –> Service Parameters
Correct Answer: C
Question 13:
An engineer configures a Cisco Unified Border Element and must ensure that the codecs negotiated meet the ITSP requirements. The ITSP supports G.711ulaw and G.729 for audio and H.264 for video. The preferred voice codec is G.711. Which configuration meets this requirement?
A. Voice class codec 10 codec preference 1 g711ulaw codec preference 2 g729r8 video codec h264 dial-peer voice 101 voip session protocol sipv2 destination el64-pattern-map 1 voice-class codec 100
B. Voice class codec 10 codec preference 1 g711ulaw codec preference 2 g729r8 dial-peer voice 101 voip session protocol sipv2 destination el64-pattern-map 1 voice-class codec 10
C. Voice class codec 10 codec preference 1 g711ulaw codec preference 2 g729r8 video codec h264 dial-peer voice 101 voip session protocol sipv2 destination el64-pattern-map 1 voice-class codec 10
D. Voice class codec 10 codec preference 1 g729r8 codec preference 2 g711ulaw video codec h264 dial-peer voice 101 voip session protocol sipv2 destination el64-pattern-map 1 voice-class codec 10
Correct Answer: C
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/voice/cube/configuration/cube-book/cube-codec-basic.html
Question 14:
DRAG DROP
Drag and drop the SNMPv3 message types from the left onto the corresponding definitions on the right.
Select and Place:
Correct Answer:
Question 15:
What must be configured on a Cisco Unity Connection voice mailbox to access the mailbox from a secondary device?
A. mobile user
B. alternate names
C. alternate extensions
D. Attempt Forward routing rule
Correct Answer: C
To access a Cisco Unity Connection voice mailbox from a secondary device, you must configure an alternate extension for the mailbox. This is a phone number that is different from the mailbox\’s primary extension. When you call the alternate extension, you will be prompted to enter the mailbox\’s PIN. Once you have entered the PIN, you will be able to access the mailbox just as you would if you were calling from the primary device.